Agree Setup Privacy Policy
Heat pumps
x-change dynamic AW I
x-change dynamic AW E
x-change dynamic terra BW I
x-change dynamic water WW I
Supplier: Kermi
Is used to generate heat through the heat pump removing thermal energy from the heat source (air, water, ground) and converting it into heating warmth.
Heat pump with x-center base:
1. Connect up the heat pump in accordance with the instructions included in the scope of delivery.
2. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
Connection via commercially available electricity meter with S0-interface
Supplier: All PV solar panel systems
Transparent illustration of energy flows in the photovoltaic system, additional power generators, and electrical consumers. Shows feed, own consumption, and sourcing from grid, giving an indication of the potential available to optimise own consumption. Connection of a heat pump, as well as individual scenes allow optimised increase in own consumption.
PV solar panels with x-center base:
1. Connect up the electricity meter in accordance with the instructions included in the scope of delivery.
2. Set parameters for S0-pulse in the system control.
x-net comfort control
Supplier: Kermi
The energy efficient single room control controls, regulates, and monitors the room temperature according to the settings selected. The feel-good climate can be individually set for each room and can be automated with timer programmes.
Panel heating/cooling with x-center base:
1. Connect up the underfloor heating in accordance with the instructions included in the scope of delivery.
2. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
Central domestic ventilation
x-well S180
x-well S280
x-well S370
x-well S460
x-well F170
Supplier: Kermi
The central domestic ventilation manages the air exchange throughout the appartment or the entire house. The inside air is sucked out and the fresh air is fed in.
Domestic ventilation with x-center base:
1. Connect up the heat domestic ventilation in accordance with the instructions included in the scope of delivery.
2. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
Dezentrale Wohnraumlüftung
x-well D12 Pendellüfter
Anbieter: Kermi
Die dezentrale Wohnraumlüftung dient zur Be- und Entlüftung von Wohnungen und Häusern. Aufgrund der Bauweise ohne Lüftungskanäle ideal für Renovierungen geeignet.
Dezentrale Wohnraumlüftung mit x-center base:
1. Die Wohnraumlüftung gemäß der im Lieferumfang enthaltenen Anleitung verkabeln.
2. Anlernvorgang unter Geräte anlernen „Manuell hinzufügen“ im x-center Base starten und Lüftung Dezentral auswählen.
3. Die am Bediengerät auftauchende Meldung bestätigen.
Hinweis: Anbindung an die x-center Base lediglich mit Touch Steuerung und Smart Home Anbindungsmodul möglich.
Kermi EnOcean radiator controller
Supplier: Kermi
Prod. code: BX04000001K
Is used to control the Kermi radiator. Full remote access of all control parameters, e.g. actual or target value, battery status.
1. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
2. Short press of a button on radiator controller and wait until two opposing arrows appear on the display.
Tap wireless light actuator adapter plug
Supplier: Eltako
Prod. code: TF100L-230V
Is used to switch a light or another electrical consumer. Functions such as switching on/off and on/off duration can be configured. The receiver can be controlled through additional teaching-in of a switch, manual transmitter, or motion sensor.
1. Start the teach-in process under Teach-in devices “Add manually” in the x-center base and select Eltako switch actuators.
2. After plugging into the socket, the teach-in mode is automatically active for 2 minutes.
Tap wireless universal dimming actuator
Supplier: Eltako
Prod. code: TF61D-230V
The dimming actuator is used to dim and switch the lighting. Functions such as switching on/off, on/off duration, and levels of brightness can be configured. The receiver can be controlled through additional teaching-in of a switch, manual transmitter, or motion sensor.
1. After connecting the supply voltage, the teach-in mode is automatically active for 2 minutes (delivery status).
2. Within the 2 minutes, start the teach-in process under Teach-in devices “Add manually” in the x-center base and select the Eltako dim actuator.
Tap wireless light actuator
Supplier: Eltako
Prod. code: TF61L-230V
Is used to switch a light or another electrical consumer. Functions such as switching on/off and on/off duration can be configured. The receiver can be controlled through additional teaching-in of a switch, manual transmitter, or motion sensor.
1. After connecting the supply voltage, the teach-in mode is automatically active for 2 minutes (delivery status).
2. Within the 2 minutes, start the teach-in process under Teach-in devices “Add manually” in the x-center base and select Eltako switch actuator.
Tap wireless relay actuator
Supplier: Eltako
Prod. code: TF61R-230V
Is used to switch a light or another electrical consumer. Functions such as switching on/off and on/off duration can be configured. The receiver can be controlled through additional teaching-in of a switch, manual transmitter, or motion sensor.
1. After connecting the supply voltage, the teach-in mode is automatically active for 2 minutes (delivery status).
2. Within the 2 minutes, start the teach-in process under Teach-in devices “Add manually” in the x-center base and select Eltako switch actuators.
Note: Reset actuator to delivery state
see operating manual of the manufacturer
Easyclick receiver 1 channel BIDI
Supplier: Peha
Prod. code: 451 FU-EBI(M) o.T.
Is used to switch a light or another electrical consumer. Functions such as switching on/off, on/off duration can be configured.
1. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
2. Briefly press the Learn button (LRN) on the switch actuator (1 sec.), the button will flash red. Then press the button again for approx. 2 sec. The button briefly flashes green.
Kermi switch actuator with energy measurement 1 channel
Supplier: Kermi
Prod. code: BX02000008K
Is used to switch the Kermi e-heating rod or a light or another electrical consumer. Functions such as switching on/off, on/off duration can be configured. The switch actuator has an integrated energy measurement.
1. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
2. Briefly press the Learn button (LRN) on the switch actuator (1 sec.), the button will flash red. Then press the button again for approx. 2 sec. The button briefly flashes green.
Window/door contact
Supplier: NodOn
Prod. code: SDO-2-1
The window/door contact send the state of the window or the door to x-center base, as soon as it changes (open/closed).
1. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
2. Press the Learn button on the window/door contact for 1 sec.
Window/door contact
Supplier: Thermokon
Prod. code: SRW01
The window/door contact send the state of the window or the door to x-center base, as soon as it changes (open/closed).
1. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
2. Press the Learn key on the window/door contact for 1 sec.
Tap wireless blind actuator
Supplier: Eltako
Prod. code: TF61J-230V
Is used for switching and controlling shutters and blinds. Position detection allows individual positioning of the shutters, e.g. based on the current position of the sun. The receiver can be controlled through additional teaching-in of a wireless switch or a wireless remote control.
1. After connecting the supply voltage, the teach-in mode is automatically active for 2 minutes (delivery status).
2. Within the 2 minutes, start the teach-in process under Teach-in devices “Add manually” in the x-center base and select the Eltako blind actuator.
EnOcean blind 2-channel
Supplier: Peha
Prod. code: D452 FU-EBI JR o.T.
Software status: 230JR_345 (2017)
Is used for switching and controlling shutters and blinds. The blind actuator has a measurement chip for position detection. This then allows individual positioning of the shutters, e.g. based on the current position of the sun.
1. Press the Learn button on the blind actuator for 1 sec.
2. Start the teach-in process under Teach-in devices “Add manually” in the x-center base and select the Peha EnOcean blind actuator.
CO2 sensor
Supplier: Afriso
Is used to continuously monitor the concentration of carbon dioxide (CO2) in the room air.
1. Plug sensor into socket (connect the supply voltage).
2. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
3. Press the Learn button on the sensor.
Combined wireless sensor CO2/temperature/rel. humidity
Supplier: Thermokon
Prod. code: SR04 CO2
Is used to detect carbon dioxide (CO2), temperature, and relative humidity (optional) in living space. The CO2 content is used as a verifiable indicator for the room air quality. The lower the CO2 content, the better the air quality.
1. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
2. Press the Learn button on the sensor.
Wireless smoke alarm ASD 10
Supplier: Afriso
Is used to warn reliably of fires and smoke emission. Acoustic warning, as soon as a certain amount of smoke has been registered.
1. Start the teach-in process under Teach-in devices “Add manually” in the x-center base and select Afriso smoke alarm.
2. Press the Learn button in the sensor.
Wireless smoke alarm white
Supplier: Eltako
Prod. code: EAN 4010312312308
Is used to warn reliably of fires and smoke emission. The alarm notification is given as a loud intermittent sound every 0.5 seconds.
1. Start the teach-in process under Teach-in devices “Add manually” in the x-center base and select the EnOcean wireless smoke alarm.
2. Press the Learn button on the housing until the warning sounds.
Tap wireless switch tracker
Supplier: Eltako
Prod. code: TF-TTB
The switch tracker is used for presence detection. Automatic detection of presence and absence. If you enter the building with the switch tracker, then the predefined devices are activated and are deactivated again when you leave. In addition to that, the tracker has a blue pushbutton as a freely configurable wireless switch.
1. Open the tracker housing.
2. Set the slide switch to “Tr”.
3. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
4. Press the learn button on the back of the switch tracker (or next to the battery).
To teach-in as switch:
1. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
2. Press button briefly (blue pushbutton).
Wireless ceiling multi-sensor 360°
Supplier: Thermokon
Prod. code: SR-MDS BAT
The ceiling multi-sensor is used to detect movement and brightness in living space and offices. The multi-sensor can also be used for downstream switch actuators e.g. for constant lighting control.
1. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
2. Open the cover on the multi-sensor and press the Learn button for 1 sec.
Indoor siren AIS 10
Supplier: Afriso
Is used to effectively warn against break-in, danger and the detection of leaks.
1. Plug sensor into socket (connect the supply voltage).
2. Start the teach-in process under Teach-in devices “Add manually” in the x-center base and select Afriso siren.
3. Press the Learn button on the sensor.
Wireless outdoor temperature sensor
Supplier: Thermokon
Prod. code: SR65
Wireless outdoor temperature sensor to detect temperature outside, or in cold stores or greenhouses, as well as in production halls and warehouses.
1. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
2. Open the cover on the probe and press the Learn button (LRN) for 1 sec.
WaterSensor eco
Supplier: Afriso
For the detection of accumulations of water on defined horizontal surfaces. Maintenance-free and independent of external power sources.
1. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
2. Press the red piston valve on the sensor once.
Multi-sensor MS + wireless weather data transmitter module
Supplier: Eltako
Prod. code: Multisensor MS + FWS61-24V DC
Detects seven momentary readings of weather items: brightness (from three cardinal points), twilight, wind, rain, and ambient temperature.
1. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
2. Once the weather station has power, it automatically transmits a learning package for the first 3 min.
Temperature sensor FTM
Supplier: Afriso
Is used to measure and provide information on room temperatures.
1. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
2. Open the cover on the probe and press the Learn button (LRN) for 1 sec.
Outdoor humidity temperature sensor
Supplier: Eltako
Prod. code: FAFT60
Is used to determine temperature and humidity. Continuously measures the relative humidity and temperature.
1. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
2. Apply the enclosed blue magnet below the position on the sensor marked ■ to attach it to the side wall.
Wireless outdoor light sensor
Supplier: Thermokon
Prod. code: SR65 Li
Wireless outdoor light sensor to automatically control blind systems. Can also be used to control light at sunset.
1. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
2. Open the cover on the probe and press the Learn button (LRN) for 1 sec.
EnOcean Easyclick Mini handheld transmitter, 4 channels
Supplier: Peha
Prod. code: D 450 FU-HS4
The mini handheld transmitter has no battery and switches the receiver connected to the Kermi x-center base. Light control, system control (ventilation system, heat pump, underfloor heating) and control of blinds can be realised.
1. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
2. Press button briefly.
Wireless switch FT4F
Supplier: Eltako
Prod. code: FT4F
The switch has no battery and switches the receiver connected to the Kermi x-center base. Light control, system control (ventilation system, heat pump, underfloor heating) and control of blinds can be realised.
1. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
2. Press button briefly.
Wireless switch FT55
Supplier: Eltako
Prod. code: FT55
The switch has no battery and switches the receiver connected to the Kermi x-center base. Light control, system control (ventilation system, heat pump, underfloor heating) and control of blinds can be realised.
1. Start the teach-in process under Teach-in devices “Automatic search” in the x-center base.
2. Press button briefly.